Poolstar
Poolstar — French manufacturer of Poolex pool heat pumps, Freeflo filtration pumps and pool accessories.
Poolstar pool pumps and spare parts
Poolstar equipment is a familiar sight on domestic pools across Europe, and the Freeflo Racer filtration pump is the part of the range most owners come to know best. It is the component that moves every litre of water through the filter, several hours a day, every day of the season. Here you will find the complete pump as well as the individual components behind it: motors in several outputs, run capacitors, mechanical seals, fan covers, impeller rings, drain plugs and the small fixings that are easy to lose and awkward to source separately.
Buying a single component instead of a whole pump is usually the sensible route. A Freeflo Racer with a failed capacitor or a weeping shaft seal is otherwise a perfectly serviceable unit, and the hydraulic end of the pump often outlives the electrical end by a wide margin.
The Freeflo Racer range
The Freeflo Racer is a single-phase filtration pump supplied in a series of motor outputs, which is the first thing to establish before ordering anything electrical. The spare parts listed here are grouped around those outputs:
- 0.25 kW and 0.37 kW — share a common single-phase motor reference (R0021), a dedicated fan blade (R0034) and their own fan cover (R0028).
- 0.55 kW — motor R0022, with the larger fan cover shared across the upper outputs.
- 0.75 kW — motor R0023.
- 1.10 kW — motor R0024, paired with the 25 µF run capacitor.
- Shared components — mechanical seal (R0025), pump foot (R0026), base screws (R0027), capacitor housing with fixings (R0030), impeller ring (R0036) and drain plug with O-ring (R0020).
Because several items cross over between outputs and several do not, the output marked on the motor plate is the single most reliable starting point for identification.
Which parts fail first
Filtration pumps tend to fail in predictable ways, and the parts list reflects that. Knowing the usual suspects saves a lot of guesswork at the poolside:
- Run capacitors — a pump that hums but will not start, or that trips the breaker on start-up, very often has a tired capacitor. Three values are listed: 12 µF (R0031), 20 µF for 0.55 and 0.75 kW (R0032) and 25 µF for 1.10 kW (R0033). Always match the microfarad value printed on the old capacitor rather than estimating.
- Mechanical seal — R0025 is the shaft seal between the wet end and the motor. Water dripping from the join between pump body and motor, or rust staining on the motor face, points here. Left alone, a leaking seal takes the motor bearings with it.
- Drain plug and O-ring — R0020 is removed and refitted at every winterisation, so the O-ring is a routine replacement rather than a repair.
- Fan, fan blade and fan cover — the motor relies on airflow for cooling. A cracked cover (R0028, R0029), a damaged blade (R0034) or a broken cooling fan (R0035) leads to overheating and nuisance cut-outs.
- Foot and fixings — the motor base (R0026) and base screws (R0027) corrode in damp plant rooms and are cheap to renew while other work is being done.
Identifying the right part before ordering
Work from three pieces of information. First, the motor rating plate, which gives the kW output and confirms single-phase supply. Second, the R-number, where it is still legible on the old component or on the exploded diagram supplied with the pump; these references run through the whole Freeflo Racer parts list and are the quickest way to a match. Third, a measurement. For seals and O-rings, note the inner and outer diameter and the thickness with a vernier or a steel rule before ordering, since a seal that is close but not identical will leak.
If the pump has already been opened, photograph the assembly before removing anything. The order of shaft seal, impeller ring and fixings is much easier to reverse from an image than from memory.
Poolstar at PoolParthub.com
Stocked here are complete Freeflo Racer filtration pumps alongside the full spread of service components: single-phase motors from 0.25 kW to 1.10 kW, the three run capacitor values and their housing, mechanical seals, impeller rings, cooling fans, fan blades and covers, motor feet, base screws and drain plugs with O-rings.
The aim is to keep a working pump working. Most of these items are low-cost parts that decide whether a pump is repaired in an afternoon or replaced entirely, which is why the range is carried down to the individual screw pack rather than stopping at assemblies.