Skip to content
Account

Ocean

Ocean pool fittings and installation parts

Ocean parts belong to the plumbing and shell-penetration side of a swimming pool: the components that are built into the wall or the deck and then stay there for the life of the installation. Here you will find white ABS fittings and extension pieces in standard sizes, suitable for new builds, for renovations where an old penetration has to be rebuilt, and for repairs where a cracked or leaking fitting has to be cut out and replaced like for like.

Because these parts are embedded in concrete, liner or panel work, the important thing is not the brand badge but the geometry: thread size, pipe diameter, socket type and the external dimensions of the housing. The notes below explain how to read those details off the product names so that the replacement matches the hole that is already there.

Inlet fittings and how to identify the right one

The inlet fitting in this range is an ABS unit in 2″ male thread with a 50/63 mm glue socket and glue spigot, finished in white and supplied with A4 stainless steel inserts and M5 stainless threads. Each of those figures tells you something you can check before ordering:

  • 2″ male thread — the pipe-side connection. It screws into a female 2″ socket, so the counterpart on your pipework must be a matching female thread.
  • 50/63 mm glue socket and spigot — the same body accepts 50 mm PVC pipe into the socket, while the spigot allows a 63 mm fitting to be glued over it. That dual arrangement is what makes one part fit two common pipe sizes.
  • A4 stainless inserts — threaded metal inserts moulded into the plastic so the face plate screws do not strip the ABS. A4 is a marine-grade stainless classification, used where chlorinated water and plastic meet.
  • M5 threads — the screw size for the cover or face plate. Measure an existing screw before reusing old hardware, as M4 and M5 are easy to confuse by eye.
  • White ABS body — standard pool white, so it sits unobtrusively against liner, tile or rendered finishes.

When replacing an existing inlet, measure the hole in the wall and the thread on the pipe stub rather than relying on the look of the old part. Fittings from different eras share an outline but differ in thread depth and flange diameter.

Enlargement and extension pieces

The second item in the range is an enlargement measuring 250 mm x 385 mm in white, standard type. Rectangular parts in this format are used where a built-in housing has to be brought forward or where an opening has to be adapted to a different finished surface level — for example when tiling, rendering or a new liner changes the depth from the structural wall to the visible face.

Before ordering any extension or enlargement component, take three measurements: the external length and width of the existing opening or housing flange, the depth you need to gain, and the bolt or screw pattern if the part is fixed rather than bonded. Comparing those three figures with the stated 250 mm x 385 mm dimensions is the only reliable way to confirm a fit, because housings that look identical from the pool side can differ behind the wall.

Installation and service notes

A few habits make embedded fittings last and make future service easier:

  • Dry-fit first — assemble the parts without solvent cement to confirm alignment and depth, then mark the orientation before gluing.
  • Use the correct cement — PVC solvent cement is intended for PVC pipe; where ABS and PVC meet, use an adhesive rated for that combination and follow the maker’s instructions.
  • Do not over-tighten threads — plastic threads split under excessive torque. Use PTFE tape or a suitable thread sealant and tighten by hand plus a modest turn.
  • Protect the stainless inserts — keep grit out of the M5 threads during building work, and replace corroded screws rather than forcing them.
  • Record what you fitted — note the thread and pipe sizes somewhere, as the information disappears once the fitting is set in the wall.

Ocean at PoolParthub.com

Here we list the Ocean items that are called for most often during installation and renovation work: a white ABS inlet fitting with 2″ male thread, 50/63 mm glue connections and A4 stainless inserts with M5 threads, and a 250 mm x 385 mm white enlargement in the standard type. Both are the kind of component that is only noticed when it fails or when a rebuild forces a change of dimensions.

The range is kept deliberately focused on these structural, built-in parts so that the specifications on the page are the ones that matter when matching an existing pool. If you are unsure which variant suits your installation, measure the thread, the pipe diameter and the opening, and compare those figures with the details given in each product listing.