Skip to content

Filters

Filter spare parts and exploded views

A sand filter is one of the few pieces of pool equipment that is expected to run for a decade or more, which is exactly why individual components need replacing long before the tank itself does. Lid seals flatten, manometers stop reading, laterals crack, multiport valve gaskets harden and drain plugs weep. Here we list the component drawings behind the filter tanks and valves, so a single worn part can be identified by its position on the view and ordered on its own rather than replacing a complete vessel.

What the range covers

The listings follow the AstralPool filter families, from small domestic vessels through to industrial tanks, along with the valves that sit on top of or beside them. Exploded views are grouped by filter series and, where relevant, by tank diameter and outlet configuration, because the internals differ between a top-mounted and a side-mounted version of the same shell.

  • Ms series – views for Ms800 and Ms950 tanks and their internal and external components.
  • Verona – drawings covering the D.400, D.500 and D.600 diameters.
  • Viena – side outlet versions, listed under separate references for each build.
  • Teide industrial – larger commercial vessels with their own manifold, lid and connection parts.
  • Stainless steel filters – tanks with locking lid, including heights in the 800 to 1400 range.
  • Valves – UVE top valve assemblies and Top Blown Filter Plus valves such as FTM480 and FTM660.

Parts that wear out first

Most filter faults come down to a handful of components, and recognising the symptom usually points straight at the part. Sand returning to the pool through the inlets suggests a broken lateral or a cracked diffuser. Water escaping from under the lid after a backwash points to a tired lid seal or a clamp that has lost tension. A pressure gauge that never moves, or sits at zero with the pump running, has usually failed internally.

  • Lid and collar seals – flat gaskets and O-rings that compress over time and leak once disturbed.
  • Laterals, manifolds and diffusers – the internal filtration elements that hold the media in place.
  • Multiport and top valve parts – gaskets, spindles, handles and sight glasses.
  • Pressure gauges and air bleeds – small fittings that are easy to replace and essential for monitoring.
  • Drain plugs and sand drain assemblies – threaded parts with their own seals.
  • Clamps, bolts and locking rings – hardware that corrodes faster than the tank it holds together.

Finding the right part on an exploded view

Each view shows the filter broken down into numbered positions, with a reference against every number. Start from the model and size cast or labelled on the tank itself, open the matching drawing, then find the component in the illustration and note its position number. That number ties directly to the part reference, which avoids the common mistake of ordering a visually similar gasket from a different tank diameter.

Where a series exists in several diameters, as with the Verona D.400 to D.600, confirm the diameter before selecting. The same applies to outlet position: a side outlet build and a top-mounted build can share a shell but use different connection and internal parts. Industrial tanks such as the Teide range are listed under individual references for each size, so the reference printed on the data plate is the quickest route to the correct view.

Measuring and matching before you order

If the label has faded, measurements will usually resolve it. Measure the tank diameter across the widest point of the shell, the overall height, and the thread or union size at the inlet and outlet. For seals, measure the inner diameter, outer diameter and thickness of the old gasket while it is still in one piece, and note whether it is a flat ring or a round-section O-ring. For valves, check whether the connection is 1½ or 2 inch and whether the valve mounts on top of the tank or on the side.

Filters at PoolParthub.com

Here you will find exploded views and component references for domestic, commercial and stainless steel filter tanks, together with the top-mounted and side-mounted valves used with them. Listing parts by drawing position makes it practical to repair a filter rather than replace it, which is usually the cheaper and faster route back to clear water.

The range is organised around the model families above so that a reference taken from a data plate, an old gasket or a service note leads to the right component. If a filter is older and the markings are gone, the measurements described here are normally enough to identify the series and the part.