Skip to content

Hardware & seals

Hardware and seals for pool equipment

Most pool repairs do not fail on the big components. They fail on a sheared screw, a lost wheel pin, a split locking clip or a flattened O-ring that no longer holds pressure. Here you will find the small mechanical and sealing parts that keep pumps, filters, salt chlorinators, automatic cleaners, covers and equipment housings working, with references from Pentair, Zodiac, Fluidra and AstralPool.

What the range covers

The listing brings together several families of small parts that are usually sold separately from the main unit:

  • Screws and fasteners — items such as the Pentair mounting plate hex washer head screw 3/8-16 x 1 in., supplied in a pack of four, for refitting plates and brackets.
  • Pins, clips and axles — the Zodiac MX10 wheel pin, Aquabot black axle pins in packs of two, plastic locking pins, the lock pin for the Super Brush and hut pin retaining pins.
  • Hinges and bushes — equipment housing hinges with and without pin, the underground pool shelter hinge, and pool cover roller support bushes supplied with their pin.
  • Caps, tanks and supports — HydroSpin compact outlet caps, hydrocyclone pre-filter top caps, support tubes, support rings, support brackets and pre-filter tanks.
  • Electrical connectors — four-pin female connectors and the four-pin RS485 speed drive connector used on variable speed drive wiring.
  • Seals and gaskets — O-rings, flat gaskets and lid seals for lids, unions, housings and pre-filter bodies.

Finding the right pin, clip or fastener

Hardware is rarely described on the machine itself, so the fastest route is the exploded view in the manual for your model. Each item carries a position number, and that number maps to a manufacturer reference such as R354290, A3383PK or 4404310102. Ordering by reference avoids the common trap of two visually identical pins with different shank diameters.

If no documentation is to hand, measure the old part with a calliper before ordering. For threaded items, note both the thread and the length: a marking such as 3/8-16 x 1 in. describes an imperial thread, and forcing a metric screw into an imperial boss will strip the housing. For pins and axles, record the overall length and the diameter at the plain section rather than at a worn end. Check the pack quantity as well, since some items are listed singly and others in packs of two or four.

Measuring seals and O-rings before ordering

An O-ring is defined by two dimensions: the inner diameter and the cross-section, or cord thickness. Measure both on a seal that has been removed and left to relax, and treat the result as a guide only — a seal that has been compressed and heat-cycled for several seasons will almost always read smaller and flatter than the new part. Where the original is badly deformed, measure the groove it sits in instead.

Flat gaskets need outer diameter, inner diameter and thickness. Match the manufacturer reference wherever possible rather than choosing by appearance, because seals that look the same are often moulded in different compounds depending on whether they face chlorinated water, heat or UV exposure.

Pre-filter and housing components

A sizeable part of this section covers the HydroSpin and Hidrospin hydrocyclone pre-filters, including the compact pre-filter tank, the top cap, the outlet cap, the support tube, the support ring and the support bracket. These parts take the mechanical load of a water-filled body, so cracked brackets and tired caps are worth replacing as a set rather than one at a time. Note whether your unit is the standard or the compact version before ordering, as the bodies and their caps are not interchangeable.

The same applies to housing and cover hardware. Hinges are listed both with and without their pin, and ladder and cover parts such as the pin clip unit for a security above-ground ladder or the roller support bushes are specific to the frame they were designed for.

Hardware & seals at PoolParthub.com

Here we list hundreds of small components across the Pentair, Zodiac, Fluidra and AstralPool ranges — fasteners, pins, clips, axles, hinges, bushes, connectors, caps and sealing parts — so that a repair does not stall for want of a part worth a fraction of the machine it belongs to.

Each item is shown with its manufacturer reference and, where relevant, the pack quantity, so you can cross-check against the exploded view for your model before ordering. If you are already working on a unit, it is worth adding the seals and pins that sit alongside the failed part while the housing is open.