Ga naar de inhoud

Kripsol

Kripsol pump and filtration spare parts

Kripsol circulation pumps are a common sight in domestic and semi-public pool plant rooms across Europe, and because the wet end and the motor end wear at different rates, most of these pumps can be kept running for many seasons with a handful of inexpensive components. Here you will find the parts that actually fail first: bearings, mechanical seals, seal plate gaskets, drip rings, diffusers, impellers, lid nuts, pre-filter lid gaskets and the union fittings that connect the pump to the pipework.

Rather than replacing a complete unit, it is usually quicker and far cheaper to identify the single worn item. A pump that has started to whine or rumble normally needs bearings; a pump that drips from behind the impeller needs a mechanical seal; a pump that loses prime or struggles to hold suction often needs nothing more than a pre-filter lid gasket or a new union O-ring.

Which Kripsol series are covered

The range is built around the most widely installed Kripsol pump families, and many components are shared between them, so one part number often fits several models.

  • Koral and Koral KS / KSE: housings, diffusers, seal plate gaskets, casing flange screws, lid nuts and stud bolts, plus impellers such as the KSV300 turbine for the 3 HP version.
  • Mini Kapri and Kapri: pump housings, shaft slingers for the Ø19 mm shaft, lid screw nuts and motor bearings.
  • Epsilon: seal panel gaskets (also listed as RKS 160.A), diffusers and mechanical seals.
  • Ninfa and Mini Ninfa: PPE drip rings for the Ø15 mm shaft and shared lid hardware.
  • Ondine, Caribe and Delfino KS: complete mechanical seals and pre-filter covers supplied with their O-ring.
  • PRIME KPR: complete hardware screw kits for reassembly after a strip-down.

Certain fittings, such as the Ø50 mm union kit with nuts and O-rings, are listed for Koral KS alongside Hayward E-Flo, reflecting the shared connection design between those pumps.

Bearings, seals and gaskets

Motor bearings are supplied as SKF sealed units in the three sizes used across these pumps: 6202-2RSH (15 × 35 × 11 mm), 6203-2RSH (17 × 40 × 12 mm) and 6204-2RSH, the larger size fitted front and rear on motors above 1 HP. Most motors take two bearings, and it is worth renewing both at the same time, since the second one will usually have run the same hours as the first.

The mechanical seal is the barrier between the wet end and the motor. A complete seal assembly covers Caribe, Epsilon, Koral and Ondine pumps and should always be fitted together with a fresh seal plate gasket, available individually or in packs of ten for installers. Drip rings, also called slingers, sit on the shaft and throw escaping water away from the motor bearing; they are sized by shaft diameter, so check whether the shaft is Ø15 mm or Ø19 mm before ordering.

Identifying the right part before ordering

A few checks save a return. Work through them with the pump isolated and drained.

  • Read the motor plate: the model name and horsepower determine the impeller and, in many cases, the bearing size.
  • Measure before you buy: shaft diameter for drip rings, bearing bore and width for motor bearings, and union diameter for the connection kit.
  • Use the exploded view: Kripsol service drawings number each component, and matching that position number to the reference code shown in the product title is the most reliable way to order.
  • Note the reference formats: long codes such as 500100130002 identify the part, while RKS numbers appear on older diagrams for the same items.
  • Compare the old gasket: lay the worn pre-filter lid or seal plate gasket flat and check outer diameter and profile, as these flatten and harden with age.

Kripsol at PoolParthub.com

Here we list wet-end and motor-end components for the Koral, Kapri, Epsilon, Ninfa, Ondine, Caribe and Delfino families, from single screws and nuts up to complete housings, impellers and diffusers. Consumables such as gaskets, drip rings and lid nuts are offered both individually and in packs of ten, so a homeowner can buy one and a service company can stock a box.

The aim is simple: to make a repair possible instead of a replacement. Orders ship across Europe, and if a code on a pump label or service drawing is unclear, send it over and the matching component can be confirmed before you order.