Ga naar de inhoud

Verlichting

Lighting parts and underwater lights from the exploded views

Pool lighting is made up of more parts than it first appears: a niche set into the wall, a front ring or cover, a gasket, a lamp or LED unit, a cable with a gland or conduit, and a low-voltage supply feeding it all. Any one of these can fail on its own, and in most cases only that one part needs replacing. Here you will find the components drawn on the AstralPool exploded views for underwater lights, bulkhead lights and niches, listed by their own reference so that a single cover, lamp set or gasket can be ordered without changing the complete fitting.

Wat het assortiment omvat

The list spans complete lights, housings and the small parts that sit around them. Broadly it breaks down into:

  • LED units and lamps — Lumiplus and Lumiplus Rapid lights, white LED and RGB versions, and standard lamp types including PAR 56 fittings and a 300 W projector lamp with its O-ring.
  • Niches and mounting bodies — separate niches for concrete pools, prefabricated and panel pools and liner pools, since the way the body is sealed into the wall differs with each construction method.
  • Covers, front rings and trims — stainless steel and white covers, versions supplied with cable, and the Parker screws and fixings that hold them.
  • Bulkhead and mini bulkhead lights — compact plastic fittings for smaller pools and spas, where a full projector niche is not practical.
  • Spotlights and point lights — flexi spotlights running at 12 V AC and Point underwater lights in INOX and ABS with staple fittings, available in white, RGB and DMX-controlled versions.
  • Cable and sealing parts — cable conduits, glands and lamp sets supplied with cable, plus complete lighting kits for liner pools.

Finding the right part on an exploded view

An exploded view numbers every component of the fitting, so the quickest route is to match the drawing for your light and then order by the position number and its reference. The reference printed or moulded on the old part is the most reliable identifier, because visually similar covers and niches are not always interchangeable between concrete, prefabricated and liner versions.

Where no reference survives, work through the fitting from the outside in. Note whether the front cover is stainless steel or white plastic, how many fixing screws it uses, and whether the cable leaves through a gland in the body or through a separate conduit. Measure the diameter of the cover and the seating diameter of the gasket before ordering, and check the gasket thickness as well as its outside diameter — a flat ring and a moulded profile of the same width do not seal the same way.

Lamps, LED units and voltage

Before replacing a lamp or converting a standard light to LED, check what feeds it. Pool lights are normally supplied through a transformer, and items described as 12 V AC are intended for that type of supply rather than mains. The lamp format matters just as much: PAR 56 is the common standard for larger underwater projectors, which is why white, RGB and DMX versions share the same body and niche. Smaller bulkhead and point lights use their own fittings and are replaced as a unit.

If colour control is involved, the receiving light and the controller need to speak the same language — an RGB light switched by power pulses behaves differently from a DMX-addressed unit, so keep the control method consistent across the pool.

Parts that wear and when to replace them

Gaskets and O-rings are the usual culprits. They harden, take a set and eventually let water into the lamp housing, so it is good practice to fit a new seal whenever a light is opened, even if the old one looks sound. Stainless fixings and Parker screws corrode in chlorinated or salted water and are cheap to renew. Cable glands and conduits are worth inspecting at the same time, as a weeping gland will ruin an otherwise healthy lamp. Plastic covers can also craze and discolour under UV, which is a cosmetic job rather than a structural one but is often done alongside a lamp change.

Lighting at PoolParthub.com

Here we list AstralPool lighting components as they appear on the manufacturer’s exploded views: complete lights and kits, niches for concrete, prefabricated and liner pools, stainless and white covers, lamp sets with cable, conduits, gaskets and fixings, each under its own reference.

Listing parts individually means a failed seal or a broken cover does not force the replacement of a whole fitting, and an existing niche can usually be kept when the lamp inside it is upgraded. If you are unsure which drawing applies, compare the shape of the front ring and the pool construction type before selecting the reference.