Treci direct la conținut

Instalații sanitare și robinete

Plumbing and valves: exploded views and spare parts

The pipework between the pool and the plant room is usually the part of an installation that gets the least attention and does the most work. Valves are turned, closed, backwashed and left under pressure for years, and when something finally leaks or refuses to seal it is almost never the whole valve that has failed. It is a seal, a spindle, a handle, a union nut or a flapper. The exploded views in this section exist so that single component can be identified and replaced instead of cutting out and re-plumbing a perfectly good valve body.

Here you will find drawings and the associated spare parts for valves and plumbing fittings used in domestic and semi-commercial pool circuits, including Pentair valve spare parts and components for the Clear Series check valve. Each drawing lists the parts by position number with a description and a part number, so the component can be ordered on its own.

What this section covers

Pool plumbing covers more ground than most people expect, and the drawings reflect that. Typical items dealt with here include:

  • Supape cu bilă — isolation on suction and return lines, usually repairable with a new seat, O-ring set or handle rather than a full replacement.
  • Check valves — non-return valves that stop water draining back to the pool or protect a chlorinator and heater; the Clear Series check valve is a familiar example, with a serviceable flapper and lid seal.
  • Diverter and three-way valves — used to switch between skimmer and main drain, or between pool and spa, where the rotating diverter and its seal take the wear.
  • Multiport and backwash valve components — spiders, gaskets, spindles, handles and keys that determine whether the valve actually seals between positions.
  • Unions, tailpieces and adaptors — the threaded connections at pumps, filters and heaters, where a flat seal or O-ring is nearly always the cause of a weep.
  • Seals, O-rings and fixings — lid O-rings, stem seals, washers, screws and clips listed individually on the drawings.

Which parts fail first

Valves rarely fail in the body. What ages is anything made of rubber or anything that moves. Lid and stem O-rings harden and take a permanent set, so they stop recovering when the valve is operated. Check valve flappers lose their spring and start allowing backflow, which shows up as water draining out of the filter or a pump that loses its prime overnight. Diverter seals wear on one side if the valve is always turned to the same position. Handles and keys crack from being forced while the system is still pressurised.

Chemical exposure matters too. Concentrated chlorine or acid dosing downstream of a valve will shorten the life of seals close to the injection point, which is exactly why a non-return valve is fitted there and why its internals are considered a service item.

How to use an exploded view

An exploded view shows the valve pulled apart in assembly order, with a number next to every component. The accompanying table gives the position number, a short description and the part number. Working from the drawing avoids the most common ordering mistake, which is choosing a part that looks the same in a photograph but belongs to a different size or generation of the same valve.

A practical order of work: identify the valve by any label, moulding or marking on the body; confirm the pipe size and connection type; find the matching drawing; then read off the position number of the item needed. If a kit is listed, check which position numbers it includes, because seal kits often cover several items at once and are better value than buying them separately.

Measuring and checking before ordering

Where a label has faded, measurements decide the part. Useful checks include:

  • Dimensiune țeavă — measure the outside diameter of the pipe or the socket depth, and note whether the connection is metric solvent weld, imperial or threaded.
  • Dimensiuni garnitură O-ring — take the inside diameter and the cord thickness of the old ring, and measure it off the groove rather than stretched on the valve.
  • Port layout — count the ports and note how they are arranged, as two and three-port bodies share many internal parts but not all.
  • Handle and stem — check the drive shape and the fixing method before replacing a handle on its own.

Plumbing and valves at PoolParthub.com

Here we list the exploded views and the individual spare parts that go with them, so a leaking union, a tired lid seal or a failed check valve flapper can be put right with one component. The drawings are kept alongside the parts to make the position numbers easy to match.

The range includes Pentair valve spare parts and Clear Series check valve components, together with the seals, spindles and fixings that keep a circuit tight. If the valve on the installation is not immediately recognisable, the pipe size, port count and seal dimensions are usually enough to pin down the correct drawing.