Aller au contenu

Hunter

Hunter solenoid valves, MP Rotator nozzles and valve boxes

Here you will find Hunter irrigation components as they are most often needed around a pool and its surrounding garden: PGV series solenoid valves in 1″, 1½” and 2″, MP Rotator nozzles in several radius and arc bands, and pre-assembled HDPE valve boxes for three or four valves. These are the parts that control and distribute water in an automatic watering system — the zone valves that open and close on a signal from the controller, the nozzles that set how far and how wide each sprinkler throws, and the boxes that keep the valve manifold accessible but out of sight.

The PGV solenoid valve range

The PGV family is built around a fibreglass-reinforced nylon body with a 24VAC solenoid, which is the coil voltage used by standard irrigation controllers. Models in this range are rated to 10 bar and are available with flow control, so the open position can be throttled to balance zones that would otherwise take too much of the available flow.

The suffixes in the article names tell you which variant you are looking at, and they matter when ordering a replacement:

  • GB — globe body with BSP female threads, for screwing directly onto threaded pipework or fittings.
  • MM — male thread on both ends, typically used with unions or a manifold built from female fittings.
  • JT — jar-top bonnet, which unscrews by hand so the diaphragm can be reached without removing the bonnet screws.
  • -B — black body versions of the same valve.
  • Taille — 101 and 100 denote 1″, 151 denotes 1½”, and 201 denotes 2″ with a flow range of roughly 75–450 l/min.

On a valve that will not close, buzzes or weeps, the usual culprits are the diaphragm, the solenoid or debris trapped on the seat rather than the body itself. Before replacing the whole valve, note the thread size and whether it is male or female, and check whether the bonnet is screwed or jar-top — a jar-top valve and a screw-bonnet valve of the same nominal size are not interchangeable as service parts.

MP Rotator nozzles: radius and arc

MP Rotator nozzles screw into standard female-threaded pop-up bodies and deliver several rotating streams instead of a fixed fan, which suits borders and lawn strips next to paving and pool decks. The range here is split by throw distance and by arc:

  • MP800SR — short radius, around 1.8–3.5 m, including a 360° version.
  • MP-815 — around 2.5–4.9 m, in 90°–210°, 210°–270° and 360° versions.
  • MP-820 — around 4.6–7.3 m, in 90°–210°, 210°–270° and 360° versions.
  • Corner nozzle — 45°–105° over roughly 2.5–4.5 m, for narrow corners and small triangular areas.

Adjustable-arc models are set with the supplied adjustment key; the 360° versions are fixed and are identified in the product names by their colour combination, such as grey with red. When replacing a single nozzle in an existing zone, match the radius band and the arc of the one being removed. Mixing radius bands within a zone changes how evenly the water lands, because nozzles in the same band are designed to be run together.

Valve boxes and manifold access

The assembled rectangular valve boxes supplied with a filter are intended for 1″ manifolds and come ready for three or four valves. A box keeps the solenoids, wiring connections and flow controls reachable for servicing while protecting them from soil, strimmer damage and sunlight. When planning a box, allow room around each solenoid so the bonnet or jar-top can actually be removed in place, and leave the wiring with enough slack to lift a valve clear of the box.

Hunter at PoolParthub.com

Here we list Hunter zone valves, MP Rotator nozzles and valve boxes with their full model codes and article numbers, so an existing valve or nozzle can be matched exactly rather than by appearance alone. The 38 items in this brand page cover the common thread sizes, bonnet types and radius bands most often needed for repairs and extensions.

Keeping these parts alongside pool pumps, filters and fittings makes sense because the irrigation system and the pool technology usually share the same plant room, the same trenches and the same person looking after them. If you are unsure which variant you have, read the code moulded or printed on the existing part and compare it with the model names listed above.