Maytronics Dolphin E10

Maytronics Dolphin E10 exploded view & spare parts

The Maytronics Dolphin E10 is a compact, lightweight robotic pool cleaner built for above-ground pools up to around 10 metres in length. Powered by a 24 V DC motor unit and guided by Maytronics’ CleverClean™ navigation system, it completes a thorough floor-cleaning cycle in just 90 minutes — vacuuming, scrubbing and filtering in a single pass. Like every piece of precision pool equipment, the E10 relies on a handful of key components that wear with use. This exploded-view diagram and spare-parts catalogue gives you everything you need to keep your robot running in peak condition, season after season.

So finden Sie anhand der nummerierten Abbildung das richtige Teil

Every component in the E10 is assigned a unique reference number on the exploded-view diagram above. Start by identifying the area of the robot where you are seeing wear or a fault — for example, a cracked track, a torn brush strip or a damaged cable. Locate that section of the diagram and note the corresponding part number. You can then enter that number directly into the search bar on poolparthub.com, or simply click the matching item in the parts list below the diagram to go straight to the product page. If you are unsure which assembly a small component belongs to, work outward from the motor unit at the centre of the diagram — all other assemblies branch from there. Always cross-reference the part number with your robot’s serial number (found on the label on the underside of the unit) to confirm compatibility before ordering.

Main replaceable parts on the Dolphin E10

The E10 is built around a small but well-organised set of serviceable components. The Gummiketten wrap around the drive wheels on either side of the chassis and provide the grip needed to traverse the pool floor. A single scrubbing brush runs across the front of the unit, loosening algae and fine debris so the impeller can draw it in. Inside the top-access filter compartment you will find either a filter basket or ultra-fine filter panel (the E10 accepts both, giving you two levels of filtration). The Laufrad sits within the motor housing and creates the suction that pulls water — and everything suspended in it — through the filter. The Motoreinheit itself drives both the tracks and the impeller via separate drive systems. Connecting the robot to the surface is a 40-foot anti-tangle floating cable, and pool-side you have the Netzteil, which converts mains current to the safe 24 V DC the robot requires. A top handle makes lifting the E10 out of the water straightforward, and an optional Caddy keeps the robot, cable and power supply neatly stored between sessions.

Häufig verschleißende Teile und wann sie ausgetauscht werden sollten

Der Titel und brush are the highest-wear parts on any Dolphin robot and the E10 is no exception — the tracks grip rough pool surfaces every cycle, while the brush bristles are in constant contact with the floor. Inspect the tracks each season for cracking, stretching or missing lugs; a track that slips or causes the robot to veer in circles needs replacing promptly. Brush strips typically last one to two seasons depending on pool surface roughness and should be swapped out when the bristles are visibly worn flat. The filter basket or panel should be rinsed after every cycle and inspected for splits or warping; a damaged filter allows debris to bypass the media and can strain the impeller. Speaking of which, if you notice a drop in suction power, check the impeller for trapped debris or wear before assuming the motor unit is at fault. The schwimmendes Kabel endures constant flexing and UV exposure — look for kinks, cuts or brittle outer sheathing, and replace it at the first sign of damage to avoid any risk to the power supply or robot electronics. The Stromversorgung is a sealed IP 54-rated unit; if indicator lights fail to illuminate or the robot does not respond when switched on, the power supply is often the cause and should be tested and replaced as a unit.

Warum Original-Ersatzteile von Maytronics so wichtig sind

Maytronics engineers every Dolphin spare part to exact tolerances — track width, brush stiffness, filter mesh density and impeller blade geometry are all calibrated for the E10’s specific motor and hydraulic layout. Fitting a non-genuine track, for example, can alter drive tension and lead to premature wear on the drive wheels and axle bearings, creating a more expensive repair down the line. Genuine filter panels are manufactured to capture the particle sizes Maytronics specifies for the E10’s pump flow rate; off-brand alternatives may restrict flow and cause the motor to overheat, or allow fine particulates to pass straight through into your pool water. Using authentic parts also keeps your Maytronics warranty intact — third-party components can void coverage. Every part stocked on poolparthub.com is sourced directly from Maytronics, so you can order with confidence that what arrives will fit first time and perform exactly as intended.

Storing and caring for your E10 between seasons

Good maintenance habits extend the life of every part on the robot. After the final swim of the season, remove the filter basket, rinse it thoroughly and allow it to dry completely before storage — damp media left in a sealed compartment can degrade the plastic over winter. Coil the floating cable loosely (never kinked) and store it away from direct sunlight to slow UV degradation of the outer sheath. The caddy is ideal for keeping the robot elevated off concrete floors, which can flat-spot the rubber tracks if the robot sits in one position for months. Store the power supply indoors, away from frost. When you recommission the robot in spring, run through the tracks, brush and filter as described above before the first cycle of the season so any winter deterioration is caught early — and before it causes a mid-swim breakdown.