DAB
DAB pool pumps and pressure booster sets
DAB builds circulation pumps for private and public pools alongside pressure booster sets for domestic and technical water supply. The range here covers three distinct families: the EUROSWIM self-priming pool pumps with an integrated pre-filter basket, the EUROPRO high-flow centrifugal pumps with a flanged DN100 connection for larger volumes, and the ESYBOX MAX booster sets for buildings and irrigation. Alongside them sits the E.SWIM variable speed pump, intended for installations where the filtration flow is matched to demand rather than run flat out.
Because all four families use their own naming logic, the model code on the motor nameplate is the fastest route to the correct replacement or the correct successor model. Below is how those codes break down.
How the DAB ranges differ
Each family answers a different question about the pool plant room, so it helps to know which one you are looking at before comparing figures.
- EUROSWIM – self-priming filtration pumps with a transparent or removable lid and a basket that catches leaves and hair ahead of the impeller. Sizes in this listing run from EUROSWIM 50 up to EUROSWIM 300, all with 2″ female threaded suction and discharge.
- EUROPRO – high-flow centrifugal pumps in fibreglass-reinforced polypropylene with a DN100 flange, supplied in three-phase 400 V form as the EUROPRO 400T, 550T and 1000T. These are the choice for large circuits, counter-current features and commercial basins where threaded connections become a restriction.
- E.SWIM – variable speed filtration, represented here by the E.SWIM 150 at 1.1 kW with 2″ BSP connections, where speed is set to suit filtration, heating or cleaning cycles.
- ESYBOX MAX – compact pressure booster sets rated 17.4 m³/h at up to 12 bar, with 1¼″ connections, in single-phase M45/120 and three-phase T45/120 and 85/120T versions.
Reading the model code before ordering
The suffix after the EUROSWIM number tells you the supply. A T model such as EUROSWIM 100T, 150T, 200T or 300T is three-phase for a 380–400 V supply. An MIE2 model such as EUROSWIM 50MIE2, 75MIE2, 100MIE2, 150MIE2, 200MIE2 or 300MIE2 runs on 230 V single-phase. The numeric part relates to the motor rating, quoted in this listing as HP or kW depending on the version — 0.75 HP and 0.75 kW for the smallest, 1 HP for the 100, 3 HP for the 300T. Current draw is also printed on the nameplate, for example 11.8 A for the 300MIE2 and 6.9 A, 8.8 A and 9.6 A across the three EUROPRO sizes.
When replacing an existing pump, note three things before choosing: the supply available at the isolator, the port size and type on the pipework, and the physical footprint and shaft height in the plant room. Swapping a single-phase for a three-phase unit, or a 2″ threaded pump for a DN100 flanged one, means electrical and plumbing work beyond the pump itself.
Wear parts and servicing
Pool pumps are consumable at a handful of points rather than as a whole. On a self-priming filtration pump the lid seal and the basket are the first to age, because they are opened weekly and exposed to chlorinated water, sunlight and knocks. The mechanical shaft seal is the next item, and a persistent drip below the pump body is usually its signal. Impellers and diffusers suffer when the pump is run dry or when grit bypasses a damaged basket, and loss of head at the same running hours often points there.
Measure before ordering. Take the inside and outside diameter and the thickness of any O-ring with callipers rather than estimating, and use the exploded view for your model so the position number matches the part. Where a pump has been in service for years, check the model code on the nameplate rather than the invoice, as series are revised over time.
DAB at PoolParthub.com
Here you will find the DAB pool and pressure range side by side: the EUROSWIM filtration pumps in both single-phase and three-phase form, the EUROPRO 400T, 550T and 1000T high-flow centrifugal pumps, the E.SWIM variable speed pump and the ESYBOX MAX booster sets. Article numbers are listed with each item so the exact version can be confirmed against an existing installation.
Keeping the full ladder of sizes together makes it straightforward to step up or down one rating when a circuit has been extended, or to match a like-for-like replacement without changing the pipework. If a model code or a port size is unclear from the nameplate, send the details and the correct equivalent can be identified.