IT3 S.A

IT3 S.A pool pipework adhesive

Pool plant rooms are held together by PVC. Suction and return lines, manifolds, valve blocks, filter connections and backwash pipework are nearly all built from rigid or flexible PVC, and every one of those joints depends on a solvent adhesive rather than a mechanical seal. Here you will find the IT3 S.A adhesive range for exactly that job: bonding PVC pipe, fittings, unions and flexible sections into a single, watertight pressure system.

Solvent cement is not a glue in the everyday sense. It softens the surface of both the pipe and the socket so that the two materials fuse and then harden as one piece. That is why the product choice, the fit of the joint and the way the cement is applied matter far more than how much is used.

A termékcsalád tartalma

The listing on this page centres on the Bluefast PVC flexible union glue in a 500 ml tin, part reference BLUEFAST1/2. It is a solvent-based adhesive for PVC pipework of the type used throughout swimming pool and spa installations, and the description points to use on flexible PVC unions as well as standard rigid pipe and fitting connections.

A 500 ml tin is the size most installers reach for on a plant room build or a filter changeover: large enough to complete a full set of connections around a pump, multiport valve and filter, small enough that it is not left half-used for years. Tins of this size are normally supplied with a brush or applicator in the lid, which suits pipe diameters in the common pool range rather than large-bore commercial lines.

Where it is used in a pool system

Typical applications on a domestic or light commercial pool include:

• Pump and filter connections – bonding pipe tails into union nuts and tank inlet and outlet fittings.
• Valve assemblies – gluing pipe into ball valves, check valves and multiport valve ports, where leaks are hardest to reach later.
• Skimmer and return lines – joining buried or in-wall pipework to skimmer bodies, inlet nozzles and drain fittings.
• Manifolds and bypasses – assembling tees, elbows and reducers into heat pump bypass loops and dosing take-off points.
• Flexible pipe runs – connecting flexible PVC lengths into rigid fittings where a bend radius is needed around tanks or through tight plant rooms.

Preparing and making a sound joint

Most failed PVC joints are failures of preparation, not of adhesive. The sequence that gives a reliable result is straightforward:

• Cut square – use a pipe cutter or a fine-tooth saw and keep the cut at right angles so the pipe seats fully in the socket.
• Deburr and chamfer – remove internal and external burrs and put a light chamfer on the pipe end, so the pipe does not scrape the cement out of the socket as it goes in.
• Dry fit first – check the pipe enters the fitting cleanly and note the insertion depth before any cement is opened.
• Clean both surfaces – wipe off dust, water and grease; a dedicated PVC cleaner is used for this on most installations.
• Apply evenly and assemble promptly – a thin, even coat on both pipe and socket, then push home with a slight twist and hold until the joint grips.
• Let it cure before pressurising – follow the curing guidance printed on the tin, and allow longer in cold or damp conditions.

Work in a ventilated space, keep the tin closed when not in use so the solvent does not thicken, and wipe excess cement from the outside of the joint before it sets. On a pool that is being pressure tested, plan the order of work so that the joints closest to the pump are made first and have the longest to cure.

Checking what you need before ordering

Before adding adhesive to a basket, check the pipe material. Solvent cement works on PVC and PVC-U; it does not bond polyethylene, polypropylene or ABS pipework, and those systems need their own jointing method. Measure the outside diameter of the pipe and count the number of joints in the job — a single plant room rebuild can easily use more adhesive than expected once unions, valves and a bypass are included.

IT3 S.A at PoolParthub.com

Here we stock the IT3 S.A Bluefast PVC adhesive in the 500 ml tin, reference BLUEFAST1/2, as part of the wider pipework and installation section. It sits alongside pipe, fittings, unions and valves so that a filtration circuit can be ordered as a complete set rather than assembled from several sources.

Consumables like solvent cement are easy to forget and awkward to source locally at the moment they are needed. Keeping a tin on the shelf next to the spare seals and unions means a leaking joint or a filter swap can be finished the same day, rather than waiting on a second order.