Saltar para o conteúdo

Água industrial

Industrial water: pipework, expansion joints and irrigation components

Water treatment plants, pump rooms, irrigation networks and large commercial pools all share the same backbone: rigid pipework, flanged connections and the flexible elements that keep vibration and thermal movement out of the system. Here we group those heavier-duty items together, from threaded galvanised steel pipe in 6 m lengths through to rubber expansion joints in DIN flange sizes and pressure-compensating drip emitters for landscape and greenhouse watering.

Unlike the PVC and ABS fittings used around a domestic pool, most of what follows is specified by nominal size and pressure rating rather than by brand model. Getting the right part therefore comes down to reading the existing installation correctly: the thread size, the nominal bore, the flange standard and the face-to-face length of the component you are replacing.

Galvanised steel pipe in threaded lengths

The steel pipe range runs from 1/2″ up to 4″, supplied in 6 m lengths with a male thread at one end and a female socket at the other, so lengths can be screwed together into a continuous run without separate couplings. Wall thickness increases with the bore, and the pipe is produced to the EN 10255 medium series with KIWA/GASTEC marking.

  • 1/2″ and 3/4″: 2.6 mm wall, typical for branch lines, dosing lines and instrument connections.
  • 1″, 1¼” and 1½”: 3.2 mm wall, common on pump suction and discharge manifolds in smaller plant rooms.
  • 2″ and 2½”: 3.6 mm wall, used for main distribution runs and filter headers.
  • 3″: 4.0 mm wall, for larger transfer lines.
  • 4″: 4.5 mm wall, the heaviest section in the range and generally the main header size.

When ordering, remember that pipe sizes are nominal: a 2″ pipe does not measure 2″ across the outside. The reliable method is to identify the thread on the existing pipe with a thread gauge, or to measure the outside diameter and match it to the nominal size table. Galvanised pipe is cut and re-threaded on site, so allow for the length taken up inside sockets and fittings when planning a run, and dress cut ends with a suitable coating to protect the exposed steel.

Rubber expansion joints for flanged systems

Flexible expansion joints absorb pump vibration, small misalignments and thermal movement that would otherwise be transmitted into rigid pipework, flanges and pump casings. The Profec range here is built with an NBR body and DIN flanges, rated PN10, with the smaller sizes also suiting PN10/16 drilling, and covers nominal diameters of DN65, DN80, DN100, DN125, DN150, DN200, DN250 and DN300.

To select the correct unit, note three things from the existing line: the nominal diameter, the flange drilling standard and bolt hole count, and the installed face-to-face length between the two mating flanges — the DN100 joint, for example, is a 150 mm length. Fitting a joint that is too long or too short puts the bellows under permanent tension or compression and shortens its life. NBR is chosen for general water service and its resistance to oils; where a line carries aggressive chemicals, check the elastomer against the medium before ordering. Expansion joints are wear parts: perishing, surface cracking, bulging or weeping at the bead are all signs that replacement is due, and they are usually changed as a planned maintenance item rather than after failure.

Drip irrigation emitters

Alongside the pipework sits the AstralPool CETA PC pressure-compensating drip emitter, a 2 l/h unit identified by its red body. Pressure-compensating emitters hold a near-constant discharge across a range of line pressures, which keeps the first and last plant on a long lateral receiving a similar volume — useful on sloping ground and on long runs where friction loss would otherwise starve the far end. Emitters in this style are colour-coded by flow rate, so matching the colour of the units already installed is the quickest way to keep a zone uniform. Blocked emitters are the usual complaint, and adequate upstream filtration is the simplest prevention.

Industrial water at PoolParthub.com

Here you will find a broad selection of industrial water components: threaded galvanised steel pipe from 1/2″ to 4″ in 6 m lengths, NBR expansion joints from DN65 to DN300 with DIN flanges, and drip irrigation emitters, drawn from suppliers including Profec and AstralPool.

The aim is to cover the parts that keep larger water installations running rather than only the consumables of a single pool. Sizes, wall thicknesses, pressure ratings and lengths are shown in the product titles and specifications so a replacement can be matched to what is already in the ground or on the wall.