Riscaldamento
Pool heating: heat pumps, heat exchangers and solar collectors
Heating is what turns a pool from a summer feature into something usable for most of the year. Three routes are represented here, and they suit very different houses: an air source heat pump that works on its own, a heat exchanger that borrows heat from an existing boiler or buffer tank, and solar panels that cost nothing to run once they are plumbed in. Alongside the heaters sit the parts that make them work — control units, connection sizes from 32 mm hose tail up to 110 mm, and threaded unions in stainless steel and titanium.
Heat pumps from plug and play to large inverter units
The smallest units in the range are the ECO plug and play models, supplied for 230 VAC with a 32 mm connection and ratings around 2,5 to 3,5 kW, in ABS or steel housings. They are intended for small pools and above-ground installations where no dedicated power circuit is available. At the other end, the Norsup SG P inverter series covers roughly 13 kW to 26 kW in horizontal format with 50 mm unions, in single phase 230 VAC and three phase 400 VAC versions, with ABS and stainless steel cabinets and R32 refrigerant. Larger again is the Hydro-Pro PC inverter line, including a 130 kW metal-cased unit on 400 VAC with 110 mm connections for commercial and municipal basins.
- Output in kW — match to pool volume, surface area, cover use and how early in the season you want to swim.
- Tensione di alimentazione — 230 VAC for domestic single phase, 400 VAC where a three phase supply is available.
- Dimensione dell'attacco — 32 mm, 50 mm or 110 mm; check what the existing pipework and bypass will accept.
- Inverter or on/off — inverter compressors modulate output and run quieter at part load.
- Cabinet material — ABS and stainless steel panels resist pool-side humidity and chlorine vapour.
Heat exchangers for boiler and solar thermal circuits
Where a gas or oil boiler, district heating or a solar thermal store is already in place, a heat exchanger is often the simplest solution. Two families are listed: stainless steel 316 shells such as the MF 135 and MF 260 with female threads in 1″, 1 1/2″ and 2″, and the BDW16DWH x40 and x60 types with male threads; and titanium models such as the T 40 and T 75, which are the usual choice for salt electrolysis and brackish water, where chlorides attack stainless steel over time.
Selection follows the primary circuit. The available flow temperature and flow rate on the boiler side determine the transfer capacity, so a larger shell is needed when the primary water is relatively cool. On the pool side, the exchanger is plumbed after the filter and after the pump, and a three-way or manual bypass lets you throttle flow through it. Note the thread type and gender before ordering — male and female versions of the same body are not interchangeable without adaptors.
Solar panels, solar heaters and controls
Solar heating here comes as HDPE absorber panels and polycarbonate collectors. The type 1001 panel uses 25 mm hose tail connections, the type 1002 has 40 mm connections with two integrated collecting pipes, and both are rated to 4,5 bar. The polycarbonate Pyramid solar heater and the 0,55 m and 0,7 m hose-tail collectors use 32/38 mm fittings at lower working pressures, typically 1 to 2 bar, so they belong downstream of the filter on a gravity-fed or low-pressure return.
A solar circuit needs control to be worth having. The Digisol solar control unit, 230 VAC in a white housing, switches the circulation or a motorised valve according to the difference between panel and water temperature, so the pool is not cooled again on cloudy afternoons. Sensor position matters: one in the collector field, one in the return line.
Choosing and measuring before you order
- Measure the pipe — outside diameter of the existing pipework, and whether unions are metric glue or threaded.
- Check the electrical supply — phase, fuse rating and cable route to the plant room.
- Allow clearance — air source units need free air in and out, and condensate drainage.
- Record model and serial numbers — these identify the correct spare for an existing installation.
Heating at PoolParthub.com
Here you will find air source heat pumps from small plug and play models to large inverter machines, stainless steel 316 and titanium heat exchangers in a range of thread sizes and capacities, HDPE and polycarbonate solar collectors, and the control units and connection parts that tie them into the filtration loop.
The range is built around the sizes and threads that actually occur on European pool installations, so replacement is usually a matter of matching the connection and the output rather than rebuilding the plant room. If a listing leaves you unsure which capacity or thread you need, the model designations above are the fastest way to compare.