Salta al contenuto

Unità di controllo

Control units and panels for pool equipment

Behind almost every pool installation sits a housing: a cabinet, a column or a machine room enclosure that holds the electronics, the wiring and the controls together and keeps water and sunlight away from them. Here we list the casing and control components for that equipment — maintenance panels, side and back panels, top covers, thermoformed rear covers, control column bodies and the small screws and handles that hold everything in place. These parts are ordered when a panel cracks, a cover fades or warps after years outdoors, a lid no longer closes properly, or a fixing has corroded and the enclosure can no longer be closed safely.

Because the parts are structural and cosmetic rather than electrical, they are almost always model-specific. A side panel for one heat pump generation will not fit the next, even when the units look alike. That is why the listings here keep the original manufacturer reference and, where it exists, the exploded view number next to the description.

Cosa comprende la gamma

The selection spans housings and control hardware from several ranges within the Fluidra group, including Zodiac and AstralPool. Broadly, the parts fall into these groups:

  • Maintenance and service panels — the removable access panels on heat pumps and similar units, such as the Zodiac service panel references ZX108790081, ZX108840083, ZX180100017 and ZX180100018.
  • Side, back and top panels — left and right side panels like ZX180140113, ZX133260051 and ZX133270003, back panels such as ZX180100020, and connecting panel top covers including ZX180100016.
  • Control column and controller covers — bodies and lids for the 00102 control column series (00102R0001) and the thermoformed rear cover for the Guardian pool controller (72700R0011).
  • Machine room and technical housing covers — panel covers for the Playa beach pool and minipool machinery rooms, available in white (DVPLAPACGB) and coffee (DVPLAPACG) finishes.
  • Counter-current unit fronts — front panel covers for the ECC Advance and Basic ND units and the related front panel screws (4402050130) for the 11013 countercurrent swimming unit.
  • Fixings and handles — diving board fixing screws for exploded views 00068 and 00069 (4401020105) and the white-control front handle for the Yamaha Explorer Seascooter (4412010177).
  • Shower and poolside covers — replacement cover panels such as 74054R2220 for pool showers.

Finding the right panel

Panels are the parts most often ordered incorrectly, because the description alone rarely identifies them. Work from the equipment rather than from the appearance of the damaged piece:

  • Start with the unit’s rating plate — the model and serial number on the sticker inside the cabinet or on the rear of the housing tells you which generation you have.
  • Use the exploded view number — references such as 74166, 74170 and 74171 point to a specific drawing, and the position number on that drawing is what ties a panel to one model only.
  • Note left and right as seen from the front — side panels are mirrored and not interchangeable; confirm the orientation before ordering.
  • Measure before you commit — height, width and the spacing of the screw holes or clip slots are the quickest way to rule out a near-identical part.
  • Check the colour reference — covers for the same housing can exist in more than one finish, as with the white and coffee machine room panels.
  • Replace fixings with the panel — screws that have been in a wet, chlorinated environment seldom survive a second fitting.

Working safely on an enclosure

Panels and covers on control equipment are part of its protection against water ingress and accidental contact. Isolate the power supply before removing any access panel, and refit every fastener and seal that was present originally. If a gasket or foam strip is bonded to the inside of a cover, inspect it while the unit is open; a panel that sits correctly but seals poorly will let moisture reach the electronics.

Where a housing has become brittle from UV exposure, neighbouring panels are usually in the same condition. Replacing them together often avoids a second dismantling job a season later.

Control units at PoolParthub.com

Here you will find original manufacturer housing and control components listed under their own references, covering heat pump panels, control column bodies, controller covers, machine room panel covers, counter-current unit fronts and the associated screws and handles.

Keeping these parts available matters because a damaged cover is rarely a reason to replace a working unit. With the correct panel, a cabinet can be closed, sealed and returned to service, and the equipment inside stays protected for years more.