Fluidra
Fluidra pool spare parts and service components
Fluidra brings together a number of pool equipment names under one parts catalogue, which is why a single listing can run from a quarter-turn filter lateral to a stainless steel clevis pin for a robotic cleaner. Here you will find the small components that keep pumps, sand filters, suction and robotic cleaners, UV units, salt chlorinators and cover rollers working: pins, plugs, caps, seals, connectors and impeller wear parts. Many of these items are inexpensive on their own, but they are the parts that stop a machine when they shear, perish or disappear down a drain during servicing.
Qué incluye la gama
The catalogue spans several equipment families, including AstralPool, Aquabot and other Fluidra-group products, as well as replacement parts cross-referenced to Hayward pump series such as Super II, TriStar, NorthStar and EcoStar. Typical groups include:
- Piezas de filtración — laterals for Triton sand filters such as the quarter-turn ClearPro lateral 290 mm for the TR140, along with plugs, caps and internal fittings.
- Pump components — impeller rings, lower casing pins and small fixings that sit inside the wet end.
- Robotic and suction cleaner parts — axle pins, locking pins, handle clevis pins, lock pins for brush assemblies and four-pin plugs for older cleaners such as the Magnum Junior.
- Water treatment parts — drain plugs for Clair UV disinfection units and outlet caps for HydroSpin Compact units.
- Plugs and blanking caps — closing plugs in 8 mm and 11 mm, half-inch blanking plugs and plastic retaining plugs.
- Electrical connectors — four-pin male and female connectors used on cleaner and control cabling.
- Herramientas de servicio — items such as the pin replacement jig, used when rebuilding an assembly rather than fitted to the pool itself.
Pins, plugs and other small parts that wear out first
Pins take the load every time a cleaner changes direction or a handle is folded, so they are among the first items to go. Axle pins and clevis pins wear oval, plastic locking pins fatigue and snap, and stainless pins can be lost during a strip-down. Several pins are sold in packs of two because they are usually replaced in pairs on opposite sides of an assembly.
Plugs and caps fail for a different reason. Repeated seasonal removal, over-tightening and exposure to chlorinated or salted water all harden the thread and the sealing face, so a plug that held pressure last summer can weep this one. Where a plug has an O-ring, it is worth checking the ring separately rather than assuming the body is at fault.
Cómo identificar la pieza adecuada
Every item carries a manufacturer reference — for example R303604CP, 53743R0004, 04099R0001 or 3021 — and matching that reference is always the safest route. Suffixes carry meaning: PK generally indicates a multi-pack, SP marks a service or spare item, and some references are flagged as discontinued, meaning the part number remains valid for identification even though it is no longer current production.
- Start from the model, not the symptom — note the exact unit, such as Triton TR140 or HydroSpin Compact, before searching.
- Utiliza la vista desmontada — the position number on the diagram in your manual maps to a specific reference, which avoids ordering a part that looks similar but has a different shank length.
- Measure before ordering plugs — the difference between an 8 mm and an 11 mm closing plug, or between metric and a half-inch thread, is easy to miss by eye.
- Measure pins across two dimensions — length and shaft diameter together, since a clevis pin listed at 1.69 in long by 0.210 in diameter will not substitute for a shorter one.
- Check the lateral length and fitting type — sand filter laterals differ in length and in how they attach to the hub, so a quarter-turn fitting cannot be swapped for a threaded one.
Fluidra at PoolParthub.com
Here we list hundreds of Fluidra references side by side, from pump and filter internals through to cleaner hardware, UV unit plugs, cover roller fittings and the service tools used to fit them. Grouping them in one place makes it easier to order a seal, a pin and a cap together instead of tracking down three separate suppliers.
Each product is listed with its manufacturer reference and, where relevant, the equipment it belongs to, so you can check the number against your own documentation before adding it to the basket. If the reference on your old part is still legible, search for that first; if it is not, work from the model name and the exploded view and compare the measurements given in the listing.