Sta-Rite-Poolpumpe Intelliflo SW5P6R-VSD – Explosionszeichnung und Ersatzteile

Sta-Rite Intelliflo SW5P6R-VSD exploded view & spare parts

Auf dieser Seite finden Sie die vollständige Explosionszeichnung und die nummerierte Stückliste (BOM) für das Sta-Rite Intelliflo SW5P6R-VSD variable-speed pool pump — a single-phase, permanent-magnet motor pump designed for residential and light-commercial inground pool filtration. The SW5P6R-VSD uses variable-speed technology to allow the pump to run at low speeds, resulting in a significant reduction in energy consumption and noise levels. The diagram covers every serviceable component from the Intelli VFD motor assembly through to the pump body, pre-filter basket, and variable-speed drive unit. Whether you are a pool owner replacing a worn mechanical seal or a technician sourcing a new impeller, this diagram lets you pinpoint the exact part you need in minutes.

So finden Sie Ihr Teil mithilfe der nummerierten Abbildung

Every call-out number printed on the exploded-view diagram corresponds directly to a numbered row in the parts list below it — so begin by locating the general area of the pump where your issue lies (motor end, wet end, pre-filter, or control end). Once you have identified the relevant area, follow the call-out line to its number, then find that number in the BOM table to retrieve the part description and SKU. Where a SKU is shown, you can add that part straight to your basket; positions without a SKU are either sold only as part of a larger assembly or are currently unavailable individually, and the description will indicate this. Pay close attention to the quantity figure that forms part of several descriptions — for example, position 2 lists “Screw 4” and position 13 lists “Bolts & Washers 5”, meaning those fasteners are supplied as a set of four or five respectively, not as single items. Position 15 (Pump body assembly, SKU 7012197) is a sub-assembly that explicitly includes positions 16, 17, 18, and 19 — if you only need one of those sub-components, check whether it is available individually before ordering the full assembly. Position 21 covers two hardware revisions (Control Cover Assembly V1 and V2), so confirm which revision is fitted to your pump before ordering. If you are in any doubt about a part number or quantity, our customer service team is on hand to help before you place your order.

Main replaceable assemblies on the Sta-Rite Intelliflo SW5P6R-VSD

The pump is logically divided into four service zones. At the motor end, position 1 is the Intelli VFD Motor — the heart of the variable-speed system — cooled by the fan and fan cover at position 25; the motor is secured to the seal plate via the screws at position 2. The wet-end seal group centres on position 3, the Seal Plate including Mechanical Seal, with the mechanical seal itself available separately at position 4 (SKU 7012195) — this is typically the first component to inspect when the pump develops a water leak around the motor shaft. The Laufrad at position 9 (SKU 7012196) sits within the diffuser at position 11 and is retained by the impeller lock screw at position 10; worn or cracked impellers are a common cause of reduced flow and should be inspected alongside the diffuser. The O-rings at positions 5 and 12 provide the critical seals between the wet-end sub-assemblies, and their condition should be checked whenever the pump is opened for service. Moving to the pre-filter body, position 15 is the complete Pump Body Assembly (SKU 7012197), which bundles the drain plug (pos. 16, SKU 7010657), the debris basket (pos. 17, SKU 7012198), the lid O-ring (pos. 18, SKU 7012199), and the lid & lock assembly (pos. 19, SKU 7012200) — all of which are also available as individual parts. The clamp assembly (pos. 7) and clamp knob (pos. 8) hold the wet end and pre-filter body together, while the base at position 6 provides the mounting platform for the entire unit. At the control end, position 22 is the Variable Speed VSD CE Drive Intelliflo (SKU 7016557) — the electronic drive unit responsible for speed regulation — housed behind the control cover assembly at position 21 and sealed by the gasket at position 23. Finally, the slip union kit at position 20 (SKU 7012201) and the union/cover assembly at position 26 handle the hydraulic connections to the pool pipework.

Auswahl zwischen Varianten und Packungsgrößen

Several positions on this diagram carry a quantity suffix in their description rather than lettered variants, and understanding these distinctions is important before you order. Position 2 (Screw) is supplied as a pack of 4 and position 13 (Bolts & Washers) as a set of 5 — ordering a single unit is not possible for these positions, and the pack price reflects the complete set needed for a full reassembly. Position 21 presents a different type of choice: the Control Cover Assembly is listed in two hardware revisions (V1 and V2), which differ in their physical design; fitting the wrong revision may mean the cover does not seat correctly against the gasket at position 23, so always cross-reference your pump’s production date or existing cover profile before ordering. For the hydraulic connections at position 26, the description references a 50/63 mm × 2″ female-thread union with O-ring — verify your existing pipework diameter (50 mm or 63 mm) before purchasing, as an incorrect union size will require additional adapters and may affect flow performance. When in doubt, the original part fitted to the pump is always the safest reference point, and our team can help you confirm the correct variant from a photo or serial number.