Vista explodida e peças sobressalentes da bomba para piscina Sta-Rite Whisperpro S5P5R

Sta-Rite WhisperPro S5P5R vista explodida & peças sobressalentes

Esta página apresenta o diagrama completo em vista explodida e a lista de materiais para o Sta-Rite WhisperPro S5P5R Série pool pump, manufactured by Pentair. The S5P5R family spans ten model variants: S5P5RD-1, S5P5RD-3, S5P5RE-1, S5P5RE-3E2, S5P5RF-1, S5P5RF-3E2, S5P5RG-1, S5P5RG-3E2, S5P5RH-1, and S5P5RH-3E2. This is a self-priming pump available in both single-phase and three-phase configurations on the larger models. No single parent factory part number covers the entire range — each model variant is identified by its own suffix. Use the diagram and the parts list below to pinpoint the exact component you need in just a few minutes.

Como utilizar o esquema numerado para encontrar a sua peça

Every numbered call-out printed on the diagram corresponds directly to a row in the parts list table below. Start by locating the area of the pump where your problem lies — for example, the strainer housing at the front, the motor at the rear, or the wet-end internals in between. Note the call-out number closest to the component you are inspecting, then find that number in the “Pos.” column of the parts list to read off the description and SKU. Where a SKU is shown, you can add that part directly to your basket; positions without a SKU are assemblies or sub-assemblies that must be quoted or sourced as a matched unit. Be aware that the same position number can appear in more than one location on the diagram — fastener positions 16, 17, and 18 (all listed as Bolts & Washers) are a good example: each covers a different bolt group and quantity, so confirm which fixing point you are looking at before ordering. Pay particular attention to lettered and sub-lettered variants such as 1a, 1b, 1c through 1j, and the secondary sub-positions 1a1, 1c1, 1e1, 1g1, and 1i1 — these denote different motor power ratings and their matched capacitors, and selecting the wrong sub-position will result in an incompatible part. When in doubt, cross-reference the model suffix on your pump’s data plate (for example, S5P5RD-1 or S5P5RF-3E2) with the description in the parts list to confirm the match before ordering.

Principais conjuntos substituíveis na WhisperPro S5P5R

A S5P5R é construída em torno de um pequeno número de subconjuntos claramente definidos. Na parte traseira encontra-se o motor (position 1a–1j), which is the heart of the pump; the motor is a heavy-duty TEFC high-efficiency unit suitable for chlorinated and salt water pools. Directly coupled to the motor is the seal plate (posição 2), que aloja o vedante mecânico e serve de interface entre o motor e a parte húmida. O vedação mecânica itself is also available as a standalone replacement at position 15 (SKU 7016790), which is the part most commonly replaced after wear or a dry-run event. The wet-end habitação (position 7) is a BSP-threaded thermoplastic body; its engineered thermoplastic construction withstands extreme heat and resists corrosion. Inside the housing, the FunnelFlo diffuser (position 10) and high-efficiency impeller (position 13) work together to maximise water flow and energy efficiency while minimising turbulence and noise. The cesto do filtro (position 9, SKU 7010649) sits inside the pre-filter chamber; the oversized strainer basket reduces cleaning frequency, and the clear pre-filter lid allows instant inspection. The lid na posição 5 (SKU 7010690) está fixo pelo locking ring na posição 4 (SKU 7010694), e vedado pelo lid O-ring na posição 6 (SKU 7010709). O bujão de drenagem e O-ring at position 8 (SKU 7010657) provides the lower drain point on the housing body. Finally, the gasket at position 14 seals the joint between the seal plate and the wet-end housing, and is included in the convenient seal set noted at position 19, which groups together positions 6, 11, 14, and 15 for a full wet-end seal service in one order.

Escolher entre variantes e tamanhos de embalagem

A decisão de variante mais importante nesta bomba diz respeito ao motor e o respetivo condensador. Position 1 splits into lettered variants 1a through 1j, covering five power ratings — 0.55 kW, 0.75 kW, 1.10 kW, 1.50 kW, and 2.20 kW — each available in single-phase (-1) or three-phase (-3E2) form. Each single-phase motor has a dedicated run capacitor at a sub-position (1a1, 1c1, 1e1, 1g1, 1i1) with specific microfarad ratings of 16 µF, 20 µF, 31.5 µF, 35 µF, and 35 µF respectively; fitting a capacitor with the wrong µF rating can prevent the motor from starting or cause it to overheat, so always match the sub-position to your motor’s data plate reference. The impulsor at position 13 is also motor-matched: each power rating uses a different impeller trim, and the description in the parts list clearly states which model references apply, so use your pump’s full model suffix to select the correct impeller. For fasteners, positions 16, 17, and 18 each list “Bolts & Washers” but in different quantities (2, 4, and 4 respectively), while position 19 covers a separate set of Bolts, Nuts & Washers in a pair — always check the quantity listed alongside the position number to ensure you order a complete set and avoid a return visit to the pump.