Brosse à lamelles Zodiac Tornax TX R9022 - R0764900

Zodiac Tornax TX R9022 brosse lamelle R0764900

The Zodiac Tornax TX R9022 lamella brush R0764900 is the original replacement brush for Zodiac TornaX and TX series pool cleaners.
This grey lamella style brush improves grip on the pool surface and helps the robot scrub and lift dirt, algae and fine debris from the floor and lower walls,
restoring the cleaner’s original traction and cleaning performance.

Principales caractéristiques de la brosse Zodiac Tornax TX

• Original Zodiac lamella brush for TornaX and TX series pool robots.
• R9022 profile in flexible grey material for effective scrubbing and debris pick up.
• Designed to provide optimal grip on most pool surfaces except ceramic or gresite tiles.
• Improves climbing ability and stability when cleaning floors and lower walls.
• Supplied as a replacement brush identified by reference R0764900.

Détails techniques

• Marque : Zodiaque
• Série : TornaX / TX
• Type de produit : Brosse à lamelles pour robot de piscine
• Référence du fabricant : R0764900
• Model name: Cepillo TX R9022
• EAN : 9317545022772
• Couleur : Gris
• Matériau : Élastomère flexible, résistant aux produits chimiques
• Emplacement sur la vue éclatée : Généralement en position 24 sur les schémas Zodiac TornaX.

Compatibilité avec les robots de piscine Zodiac

This R9022 brush is used on several Zodiac TornaX and related cleaners that share the same roller and brush design.
It is intended as a direct replacement when the original lamella brush has the same grey R9022 profile and R0764900 part number.

• Zodiac TornaX RT 2100 et RT 3200.
• Zodiac TornaX OT 2100 et OT 3200.
• Additional RT, OT and AT references where the parts list specifies brush R9022 R0764900.
• Some compatible Gre branded robots that use the same Zodiac TornaX chassis and brush profile.

Always verify the reference R0764900 in the spare parts list of your cleaner and compare the profile and length of the existing brush.
If the part number and geometry match, this R9022 brush is the correct replacement.

Surfaces de piscine adaptées

The Zodiac TornaX TX R9022 brush is designed for most common domestic pool finishes, where it offers good grip and scrubbing performance:

• Suitable for liner, reinforced membrane, polyester shells and painted concrete.
• Suitable for many rough or smooth render finishes without ceramic tiles.
• Not recommended for ceramic or gresite tile finishes; use the dedicated gresite brush version instead.

Quand remplacer la brosse Zodiac R9022

Brushes are wear parts that gradually lose effectiveness as the lamellas round off and harden.
A worn brush can reduce traction, limit wall climbing and leave more dirt on the floor.

• Replace the brush when the lamella edges are visibly rounded, torn or strongly thinned.
• Replace the brush if the robot slips, struggles to climb or does not follow its normal path.
• Replace the brush if sections are missing or if the profile no longer sits evenly on the surface.
• Inspect the brush at the start and end of each season for signs of wear or deformation.

Consignes d'installation et d'entretien

• Disconnect the power supply or transformer before handling the pool cleaner.
• Remove the robot from the water and place it on a soft surface to avoid scratching the casing.
• Release the old lamella brush from the roller according to the procedure in the Zodiac manual.
• Clean the roller and check that there are no sharp edges or embedded debris.
• Fit the new Zodiac TornaX TX R9022 brush R0764900, making sure each lamella segment is properly seated in the roller slots.
• Check that the brush is centred and that it turns freely without rubbing on the cleaner body.

After installation, run a short cleaning cycle and observe the movement of the robot.
The cleaner should regain firm traction on the pool floor, move smoothly and resume normal climbing behaviour, with the R9022 brush keeping consistent contact with the pool surface.