Description
SEKO Pool Basic peristaltic pump 1.5 l/h 230 Vac RIC0151005
The SEKO Pool Basic peristaltic pump 1.5 l/h 230 Vac (reference RIC0151005) is a complete replacement dosing pump module for Pool Basic controllers.
It restores precise liquid dosing for pH or chlorine regulation in residential pools when the original peristaltic pump head and motor are worn or no longer
delivering the required flow and pressure.
Main features of the SEKO Pool Basic peristaltic pump
- Original SEKO Pool Basic replacement peristaltic pump with 1.5 l/h nominal flow.
- Designed for continuous service at 1.5 bar operating pressure and 230 Vac power supply.
- Supplied as a complete panel mounted pump head and motor assembly ready to install.
- Equipped with Santoprene peristaltic tube and roller head for reliable chemical dosing.
- Compatible with Pool Basic single and dual dosing units and other selected SEKO panels.
Technical specifications
- Brand: SEKO
- Product line: Pool Basic
- Manufacturer reference: RIC0151005
- Pump type: Peristaltic dosing pump module (motor + head)
- Nominal flow rate: 1.5 litres per hour
- Maximum pressure: 1.5 bar
- Power supply: 230 Vac, 50/60 Hz
- Installation: Panel mounted on Pool Basic controller or compatible panel
- Tubing material: Santoprene peristaltic tube for chemical resistance
- Tubing size: Approx. 6 × 10 mm peristaltic hose (as used on Pool Basic 1.5 l/h models)
- Typical dosed products: Liquid pH reducer, liquid chlorine or similar pool chemicals
Compatibility and typical applications
This replacement peristaltic pump is designed specifically for SEKO Pool Basic dosing systems that use a 1.5 l/h pump at 1.5 bar and 230 Vac.
It is suitable for Pool Basic single and Pool Basic double panels and can also be used on other SEKO dosing systems where the documentation specifies
replacement module RIC0151005 with the same flow and pressure rating.
The module is typically used for automatic pH regulation or chlorine dosing on private pools, where a stable and low dosing rate is required to maintain
constant water balance. It is also suitable for similar small installations that require accurate metering of liquid chemicals at low flow.
When to replace the SEKO Pool Basic peristaltic pump
Peristaltic pumps are subject to gradual wear of the tube, rollers and motor over time.
A worn pump can reduce dosing accuracy, generate noise or fail to prime correctly, which leads to unstable pH or disinfectant levels in the pool.
- Replace the pump when the controller indicates dosing faults despite correct programming and priming.
- Replace the pump if the flow is clearly reduced and the peristaltic tube has already been renewed.
- Replace the pump if the motor stalls, runs intermittently or makes abnormal noise during operation.
- Choose the complete module if both the motor and head show signs of ageing or corrosion.
Installation and connection guidelines
- Isolate the Pool Basic controller from the mains before working on the pump module.
- Note the electrical connections and hose routing on the existing pump before removal.
- Disconnect the suction and discharge hoses and remove the faulty peristaltic pump from the panel.
- Mount the new SEKO Pool Basic pump in the same position using the original fixings or panel cut-out.
- Reconnect the electrical supply leads according to the controller diagram and the markings on the new motor.
- Connect the suction line to the chemical tank and the discharge line to the injection point, respecting inlet and outlet markings.
- Prime the pump and check for leaks or air in the lines before returning the system to automatic dosing mode.
Operation, maintenance and spare tubing
Even with a new pump module, the peristaltic tube remains a wear part and should be checked regularly.
Santoprene tubing offers good chemical resistance and sealing, but it must be replaced at the intervals recommended by SEKO or sooner in heavy duty use.
- Inspect the tube periodically for flattening, cracks or visible wear and replace it when necessary.
- Rinse any external chemical spills from the pump body and panel with fresh water to prevent deposits.
- Check the suction foot valve and injection fitting to ensure that they are not blocked and that they close correctly.
- Verify dosing performance after maintenance by checking pH or disinfectant measurements against the controller set points.
With a correctly installed SEKO Pool Basic peristaltic pump RIC0151005 and regular tube replacement, the dosing system can maintain stable chemical levels
and protect pool users and equipment through reliable, low flow chemical metering.
