This page contains the full exploded-view diagram and bill of materials for the Flotide\/MEGA Heat Pump, Type Inverter, model reference Xp16Csie, carrying factory reference 7021088<\/strong>. The diagram covers every major assembly of the unit \u2014 from the outer casing and fan section through to the refrigerant circuit, water connections, and electronics box \u2014 laid out in the numbered sequence used by Flotide\/MEGA at the factory. Whether you are a pool technician diagnosing a fault or an owner replacing a wear item, the diagram and parts list below will help you pinpoint the correct component within minutes. Once you have identified the position number, simply locate the matching SKU in the table and add it directly to your basket.<\/p>\n Every numbered call-out printed on the diagram corresponds to exactly one row in the parts table below, so the two should always be read together. Begin by identifying the broad area of the unit where your part is located \u2014 for example, the fan and air-side section, the refrigerant circuit, the water-connection block, or the electronics box \u2014 then scan that region of the diagram for the relevant call-out number. Once you have the position number, find the matching row in the table to confirm the part description and, where available, the SKU you need to order. Bear in mind that the same position number can sometimes appear more than once on the diagram when a single component type is used in several locations; positions 28 and 7, both listed as “Clip”, are an example of this on the Xp16Csie. Pay particular attention to lettered variants: position 32 splits into 32a<\/strong> (LED display SHHCLEDV2MM101, SKU 7021826) and 32b<\/strong> (LED display WiFi02iMM011, SKU 7023600), which are physically different boards fitted to different build configurations of this model. Similarly, note that the same SKU (7020261) is shared between positions 37 and 52, which are distinct sensors \u2014 always cross-check the written description as well as the number. If a row in the table shows no SKU, that part is not currently listed as an individual spare; contact us before ordering to confirm availability.<\/p>\n The air-side section \u2014 positions 1 through 18 \u2014 forms the outer shell and the heat-absorption stage of the unit. The back grill (pos. 4)<\/strong> e left grid (pos. 12)<\/strong> protect the large evaporator at position 5, where outside air gives up its heat to the refrigerant. Air is drawn across the evaporator by the fan motor YDK-90-6-2 90 W (pos. 14, SKU 7021840)<\/strong> and its matched 490 mm \u00d7 125 mm clockwise fan blade with 12 mm bore (pos. 15, SKU 7010540)<\/strong>, both of which are common service items. The refrigerant circuit runs from positions 21 through 64 and contains the components that compress, expand, and transfer heat. The compressor (pos. 21)<\/strong> is kept warm during cold-weather standby by the 230 V 35 W compressor heating belt (pos. 23, SKU 7020268)<\/strong>; replacing this belt is a straightforward task that protects the compressor from cold-start damage. Refrigerant pressures are monitored by the pressure gauge (pos. 27, SKU 7010518)<\/strong> and safeguarded by the high-pressure switch 3.6\u20134.2 MPa (pos. 53, SKU 7024793)<\/strong> together with two low-pressure switch variants at positions 56 (0.1\u20130.3 MPa, SKU 7024791)<\/strong> e 57 (0.2\u20130.35 MPa, SKU 7024792)<\/strong>. The water-side section centres on the titanium heat exchanger (pos. 46, SKU 7021847)<\/strong>, which transfers heat from the refrigerant into the pool water without corrosion risk; water temperatures are monitored by dedicated sensors at positions 37 (TH5 water-out, SKU 7020261)<\/strong>, 39 (TH6 water-in, SKU 7020263)<\/strong>, and 48 (TH5 alternate water-out, SKU 7020262)<\/strong>. Water connections are made via the water connection sets at positions 41 and 44 (both SKU 7014153)<\/strong>, with colour-coded rubber rings at positions 42 (blue) and 45 (red) distinguishing flow from return. The electronics section (positions 65\u201370) houses the PC board SH0200101-V1.5 (pos. 67, SKU 7021835)<\/strong> inside a dedicated electric box, while the waterproof display box (pos. 31, SKU 7010543)<\/strong> and the display board at position 32 provide the user interface at the front of the unit.<\/p>\n The most important variant choice on this model is the display board at position 32<\/strong>. The two options \u2014 32a<\/strong> (SKU 7021826) and 32b<\/strong> (SKU 7023600) \u2014 are not interchangeable: 32a is the standard inverter LED display, while 32b is the Wi-Fi-enabled version. Before ordering, check the part number printed on your existing board, or confirm which display was fitted at the time of installation. For the water-connection seals, the colour coding matters: the blue rubber ring (pos. 42)<\/strong> and the red rubber ring (pos. 45)<\/strong> are sized and positioned to match the flow and return sides respectively, so fitting the wrong ring to the wrong port risks an improper seal. The pressure switches at positions 56 and 57 cover different operating ranges (0.1\u20130.3 MPa and 0.2\u20130.35 MPa respectively); always quote the position number and the pressure range from your existing switch label when ordering, as fitting an out-of-range switch will affect the safety cut-out behaviour of the unit. Where a position carries no SKU, please get in touch with us before purchasing a substitute, as dimensions such as thread pitch and connector type must be verified against your specific build.<\/p>","protected":false},"excerpt":{"rendered":"Como utilizar o esquema numerado para encontrar a sua pe\u00e7a<\/h3>\n
Main replaceable assemblies on the Flotide\/MEGA Heat Pump Inverter Xp16Csie<\/h3>\n
Choosing between variants and pack sizes<\/h3>\n