Ez az oldal tartalmazza a teljes sz\u00e9tszerel\u00e9si rajzot \u00e9s az alkatr\u00e9szlist\u00e1t (BOM) a Hydro-Pro Heat Pump, Type Inverter \u2014 model XP26DCSI T+<\/strong>, referenced under Hydro-Pro factory code 7018551<\/strong>. The XP26DCSI T+ is a single-phase, inverter-driven pool heat pump with a variable-speed compressor and fan that modulates output to match demand, keeping the unit both efficient and quiet. The diagram covers every numbered component from the outer casing panels through to the refrigerant circuit, electrical enclosure, and water-side connections. Use the positions listed here alongside the diagram to locate exactly the part you need \u2014 most owners and technicians narrow it down in just a few minutes.<\/p>\n Every call-out number printed on the exploded-view diagram corresponds directly to a numbered row in the parts table below the diagram. The most reliable way to work through the diagram is to start by identifying the general area of the unit where the fault lies \u2014 for example, the fan assembly area, the electrical enclosure, or the water-side pipework \u2014 and then scan only the call-out numbers within that zone. Once you have a position number, match it to the same number in the BOM to read the full part description and, where available, the SKU you need to add to your basket. Bear in mind that some position numbers appear more than once in the diagram: positions 63<\/strong> \u00e9s 70<\/strong> both refer to the Water connection set (SKU 7014153) because that set is fitted at both the inlet and outlet sides of the heat exchanger, which is entirely correct. Pay particular attention to bet\u0171s v\u00e1ltozatok<\/strong> such as positions 27a<\/strong> \u00e9s 27b<\/strong>: these share the same physical location in the diagram but are distinct, non-interchangeable parts \u2014 choosing the wrong one will mean it does not function with your existing wiring and control system. If the description in the BOM contains a model code or plug size (for example, the plug dimensions shown on positions 53, 66, 68, and 73), take note of that detail before ordering, as it is often the only distinguishing specification between otherwise similar sensors. Where a position has no SKU shown, that component is not currently stocked individually; contact us and we can advise on availability or a suitable alternative.<\/p>\n A ventil\u00e1toregys\u00e9g<\/strong> sits at the top of the unit and comprises the fan motor (pos. 19 \u2014 YDK-50-8GXX 50W, SKU 7021813), the fan blade (pos. 21 \u2014 490 mm \u00d7 125 mm with a 12 mm centre hole, clockwise rotation, SKU 7010540), the motor tube (pos. 20), and the fan motor bracket (pos. 18). The motor and blade are the components most likely to require replacement after extended outdoor use, and both carry individual SKUs. The h\u0171t\u0151k\u00f6zeg-k\u00f6r<\/strong> runs through the compressor (pos. 31), the 4-way valve (pos. 55), the electronic expansion valve (pos. 49), the fluid reservoir (pos. 32), and the filter (pos. 48), with interconnecting copper pipe runs identified at positions 50\u201352, 60, 61, and 62. The pressure protection circuit<\/strong> includes the high-pressure switch rated 3.6\u20134.2 MPa (pos. 54, SKU 7024793) and two low-pressure switch variants at positions 58 (0.1\u20130.3 MPa, SKU 7024791) and 59 (0.2\u20130.35 MPa, SKU 7024792); only one low-pressure switch is fitted per unit \u2014 refer to your service manual to confirm which specification applies to your serial number before ordering. The water side<\/strong> centres on the titanium heat exchanger (pos. 72, SKU 7021824), with the water flow switch (pos. 66, SKU 7020258) and inlet\/outlet temperature sensors TH1 and TH2 (pos. 68 and 73, SKUs 7020264 and 7020265 respectively) being the most frequently serviced components. Anti-frost protection for extended-season operation is provided by the elp\u00e1rologtat\u00f3 f\u0171t\u0151szalag<\/strong> (pos. 17 \u2014 230 V \/ 65 W \/ 2000 mm, SKU 7020274) and the kompresszor f\u0171t\u0151\u00f6v<\/strong> (pos. 33 \u2014 230 V \/ 35 W \/ 430 mm, SKU 7020270), both held in place by dedicated clips and clamps. The elektromos szekr\u00e9ny<\/strong> (pos. 84) houses the main inverter board (pos. 81, SKU 7020765) and the driver board for the 26\/35 inverter range (pos. 76, SKU 7020767), along with the 30 A relay (pos. 78) and supporting components. The waterproof display box (pos. 26, SKU 7010543) mounts on the front panel (pos. 24) and carries the LED display module, with variant options covered below. The ambient, pipe, and exhaust temperature sensor set TH3\/TH5\/TH6 (pos. 53, SKU 7020266) is supplied as a matched set with a 16\u00d74 plug and should be replaced as a unit rather than individually.<\/p>\n Poz\u00edci\u00f3 27a<\/strong> \u00e9s 27b<\/strong> represent the two LED display options for this inverter model: 27a<\/strong> is the standard inverter LED display (SHHCLEDMM101, SKU 7020256) intended for units controlled locally, while 27b<\/strong> is the Wi-Fi-enabled version (WiFi02iMM011, SKU 7023600) for units configured for remote smartphone control via the app. The two displays use different internal firmware and connector arrangements and are not substitutable for one another, so confirm which version is fitted to your unit before ordering \u2014 if in doubt, check the label on the existing display module or the wiring box (pos. 23). Similarly, the two low-pressure switches at positions 58<\/strong> \u00e9s 59<\/strong> look externally identical but are calibrated to different pressure ranges (0.1\u20130.3 MPa versus 0.2\u20130.35 MPa); fitting the wrong range can cause nuisance trips or \u2014 worse \u2014 fail to protect the compressor, so always verify the pressure rating printed on the switch body of the original before selecting a replacement. The plug sizes<\/strong> quoted in the sensor descriptions (6\u00d74 for positions 66, 68, and 73; 16\u00d74 for position 53) refer to the connector body dimensions and determine whether the sensor will mate with the main board socket, so these are not interchangeable even where the sensors look similar. For the water connection sets at positions 63 and 70, the same part (SKU 7014153) is used at both inlet and outlet, so if you are replacing both sides you will need to order a quantity of two.<\/p>","protected":false},"excerpt":{"rendered":"Hogyan lehet a sz\u00e1mozott \u00e1bra seg\u00edts\u00e9g\u00e9vel megtal\u00e1lni az alkatr\u00e9szt?<\/h3>\n
Main replaceable assemblies on the Hydro-Pro XP26DCSI T+<\/h3>\n
A v\u00e1ltozatok \u00e9s a csomagm\u00e9retek k\u00f6z\u00f6tti v\u00e1laszt\u00e1s<\/h3>\n