Hydro-Pro hőszivattyú, inverteres típus (XP26DCSI T+ típus) szerelvényi rajz és pótalkatrészek

Hydro-Pro Heat Pump, Type Inverter (XP26DCSI T+) exploded view & spare parts

Ez az oldal tartalmazza a teljes szétszerelési rajzot és az alkatrészlistát (BOM) a Hydro-Pro Heat Pump, Type Inverter — model XP26DCSI T+, referenced under Hydro-Pro factory code 7018551. The XP26DCSI T+ is a single-phase, inverter-driven pool heat pump with a variable-speed compressor and fan that modulates output to match demand, keeping the unit both efficient and quiet. The diagram covers every numbered component from the outer casing panels through to the refrigerant circuit, electrical enclosure, and water-side connections. Use the positions listed here alongside the diagram to locate exactly the part you need — most owners and technicians narrow it down in just a few minutes.

Hogyan lehet a számozott ábra segítségével megtalálni az alkatrészt?

Every call-out number printed on the exploded-view diagram corresponds directly to a numbered row in the parts table below the diagram. The most reliable way to work through the diagram is to start by identifying the general area of the unit where the fault lies — for example, the fan assembly area, the electrical enclosure, or the water-side pipework — and then scan only the call-out numbers within that zone. Once you have a position number, match it to the same number in the BOM to read the full part description and, where available, the SKU you need to add to your basket. Bear in mind that some position numbers appear more than once in the diagram: positions 63 és 70 both refer to the Water connection set (SKU 7014153) because that set is fitted at both the inlet and outlet sides of the heat exchanger, which is entirely correct. Pay particular attention to betűs változatok such as positions 27a és 27b: these share the same physical location in the diagram but are distinct, non-interchangeable parts — choosing the wrong one will mean it does not function with your existing wiring and control system. If the description in the BOM contains a model code or plug size (for example, the plug dimensions shown on positions 53, 66, 68, and 73), take note of that detail before ordering, as it is often the only distinguishing specification between otherwise similar sensors. Where a position has no SKU shown, that component is not currently stocked individually; contact us and we can advise on availability or a suitable alternative.

Main replaceable assemblies on the Hydro-Pro XP26DCSI T+

A ventilátoregység sits at the top of the unit and comprises the fan motor (pos. 19 — YDK-50-8GXX 50W, SKU 7021813), the fan blade (pos. 21 — 490 mm × 125 mm with a 12 mm centre hole, clockwise rotation, SKU 7010540), the motor tube (pos. 20), and the fan motor bracket (pos. 18). The motor and blade are the components most likely to require replacement after extended outdoor use, and both carry individual SKUs. The hűtőközeg-kör runs through the compressor (pos. 31), the 4-way valve (pos. 55), the electronic expansion valve (pos. 49), the fluid reservoir (pos. 32), and the filter (pos. 48), with interconnecting copper pipe runs identified at positions 50–52, 60, 61, and 62. The pressure protection circuit includes the high-pressure switch rated 3.6–4.2 MPa (pos. 54, SKU 7024793) and two low-pressure switch variants at positions 58 (0.1–0.3 MPa, SKU 7024791) and 59 (0.2–0.35 MPa, SKU 7024792); only one low-pressure switch is fitted per unit — refer to your service manual to confirm which specification applies to your serial number before ordering. The water side centres on the titanium heat exchanger (pos. 72, SKU 7021824), with the water flow switch (pos. 66, SKU 7020258) and inlet/outlet temperature sensors TH1 and TH2 (pos. 68 and 73, SKUs 7020264 and 7020265 respectively) being the most frequently serviced components. Anti-frost protection for extended-season operation is provided by the elpárologtató fűtőszalag (pos. 17 — 230 V / 65 W / 2000 mm, SKU 7020274) and the kompresszor fűtőöv (pos. 33 — 230 V / 35 W / 430 mm, SKU 7020270), both held in place by dedicated clips and clamps. The elektromos szekrény (pos. 84) houses the main inverter board (pos. 81, SKU 7020765) and the driver board for the 26/35 inverter range (pos. 76, SKU 7020767), along with the 30 A relay (pos. 78) and supporting components. The waterproof display box (pos. 26, SKU 7010543) mounts on the front panel (pos. 24) and carries the LED display module, with variant options covered below. The ambient, pipe, and exhaust temperature sensor set TH3/TH5/TH6 (pos. 53, SKU 7020266) is supplied as a matched set with a 16×4 plug and should be replaced as a unit rather than individually.

A változatok és a csomagméretek közötti választás

Pozíció 27a és 27b represent the two LED display options for this inverter model: 27a is the standard inverter LED display (SHHCLEDMM101, SKU 7020256) intended for units controlled locally, while 27b is the Wi-Fi-enabled version (WiFi02iMM011, SKU 7023600) for units configured for remote smartphone control via the app. The two displays use different internal firmware and connector arrangements and are not substitutable for one another, so confirm which version is fitted to your unit before ordering — if in doubt, check the label on the existing display module or the wiring box (pos. 23). Similarly, the two low-pressure switches at positions 58 és 59 look externally identical but are calibrated to different pressure ranges (0.1–0.3 MPa versus 0.2–0.35 MPa); fitting the wrong range can cause nuisance trips or — worse — fail to protect the compressor, so always verify the pressure rating printed on the switch body of the original before selecting a replacement. The plug sizes quoted in the sensor descriptions (6×4 for positions 66, 68, and 73; 16×4 for position 53) refer to the connector body dimensions and determine whether the sensor will mate with the main board socket, so these are not interchangeable even where the sensors look similar. For the water connection sets at positions 63 and 70, the same part (SKU 7014153) is used at both inlet and outlet, so if you are replacing both sides you will need to order a quantity of two.