Robinet à bille Profec en PP, DN32, 40 mm, raccord à compression, 10 bars, Safe 500, noir
Expédition 1 à 3 semaines
Certifié boutique en ligne
Retours faciles dans les 14 jours
Cherchez-vous des conseils ?
Profec Safe 500 PP Ball Valve DN32 – 40 mm Compression, 10 bar
The Profec Safe 500 is a full-bore polypropylene ball valve designed for demanding irrigation, pool pipework, and greenhouse water-distribution systems. Built to DN32 (40 mm compression ends on both sides), it delivers a rated working pressure of 10 bar and withstands continuous service at up to 60 °C, making it equally at home in cold potable-water mains and warm-water recirculation loops. The all-black PP body resists UV degradation and chemical attack, while the vivid red lever gives instant open/closed status at a glance from a distance.
Compression fittings on both ends (ØDi-1 and ØDi-2 = 40 mm) grip PE and PE-HD pipes without any solvent cement or threading — a single wrench tightens the knurled compression nuts to create a leak-free, re-usable joint. The Hytrel/EPDM seat and seal package ensures bubble-tight shut-off across the full pressure range, and the 90° quarter-turn PVC-U lever requires minimal torque even after extended periods of inactivity. Overall installed length (Lb) is 238 mm, body width (ØDf) 92 mm, and handle sweep radius (R) 64 mm, giving a compact envelope that fits standard valve boxes.
Caractéristiques techniques
- Model / Type: Safe 500
- Diamètre nominal : DN32
- Pipe connection size: 40 mm (both ends)
- Connection type: Compression (both ends)
- Matériau du corps : polypropylène (PP), noir
- Matériau de la bille et des composants internes : PVC-U
- Matériau du joint / de la siège : Hytrel / EPDM
- Poignée : à levier, rouge
- Pression de service : 10 bars
- Température maximale du fluide : 60 °C
- Operation angle: 90 °
- Total installed length (Lb): 238 mm
- Compression end outer diameter (ØDi-1 / ØDi-2): 40 mm
- Body bore diameter (ØDf): 32 mm
- Body width: 92 mm
- Handle sweep radius (R): 64 mm
- Compression nut length (each side): 40 mm
- Couleur : corps noir, poignée rouge
Compatibilité
Designed for direct push-and-tighten connection onto 40 mm outside-diameter PE, PE-HD, and LDPE pipe in accordance with standard compression-fitting dimensions. Suitable for potable cold water, irrigation mainlines, pool filtration bypass lines, and greenhouse distribution networks operating within the stated pressure and temperature limits. Not suitable for solvent-weld or threaded assemblies without an adapter fitting.
Informations complémentaires
| Marque : | Profec |
|---|---|
| Modèle / Type : | Safe 500 |
| Diamètre nominal : | DN32 |
| Type de connexion : | Compression aux deux extrémités |
| Diamètre extérieur du tuyau : | 40 mm |
| Matériau du corps : | Polypropylène (PP) |
| Ball / trim material: | PVC-U |
| Matériau du joint / de la siège : | Hytrel / EPDM |
| Poignée : | Levier, rouge |
| Couleur de la carrosserie : | Noir |
| Pression de service : | 10 bars |
| Température maximale du fluide : | 60 °C |
| Operation angle: | 90 ° |
| Total installed length (Lb): | 238 mm |
| Compression end diameter (ØDi-1 / ØDi-2): | 40 mm |
| Body bore diameter (ØDf): | 32 mm |
| Largeur de la carrosserie : | 92 mm |
| Rayon de braquage de la poignée (R) : | 64 mm |
| Compression nut engagement length: | 40 mm |
En détail
- Tool-free compression ends accept 40 mm PE/PE-HD pipe — no glue or thread tape required
- Full-bore DN32 bore minimises flow restriction and pressure drop
- 10 bar rated at up to 60 °C suits both cold irrigation mains and warm-water circuits
- UV- and chemical-resistant PP body with Hytrel/EPDM seals for long service life outdoors
- Red quarter-turn lever gives instant visual open/closed indication
- Compression ends are sized for 40 mm OD pipe only — reducers needed for other pipe sizes
- Maximum 60 °C service temperature limits use in high-temperature hot-water systems
- Single-piece body design means the valve must be cut out rather than dismantled for internal seal replacement
