Núm. Descripció Núm. de peça vista desmuntada i recanvis

Hayward SharkVac XL exploded view & spare parts

This page covers the complete exploded-view diagram and bill of materials for the Hayward SharkVac XL robotic pool cleaner, distributed in Europe by Bosta under catalogue reference 0180609. The diagram illustrates every serviceable component of this in-ground robotic unit, which scrubs pool floors, coves, walls and the waterline and operates independently from your pool’s existing filtration system. Whether you are a pool owner carrying out routine maintenance or a technician completing a full service, the numbered diagram and matching parts list below will help you pinpoint the exact component you need in just a few minutes. Several key replacement parts carry a Bosta SKU and can be ordered directly from this page.

Com utilitzar el diagrama numerat per trobar la teva peça

Every numbered call-out printed on the exploded-view diagram corresponds directly to a row in the parts list table — locate the area of the cleaner where your part lives, note the call-out number, then find that same number in the table to retrieve the description and, where available, the Bosta SKU for ordering. Work methodically from the outside of the machine inwards: start with the top cover and filter bucket area, move through the drive and wheel assembly, and finish with the internal motor and electrical components. Bear in mind that position number 1 appears multiple times in this diagram — it is used as a generic row marker for variant SKUs tied to several different assemblies, including the dome assembly, the motor assembly (SKU 7006529), the power supply (SKU 7006530), the filter cartridge refill set (SKU 7015934), and others. Always read both the description column and the SKU alongside the position number so you can be certain you have the right component. Pay close attention to lettered variants: position 33a (Brush T/S clear, SKU 7006493) and position 33b (Tube wheel with foam roller SV, SKU 7006533) share the same base number but are distinct, non-interchangeable parts. Similarly, positions 40 and 42 both describe connector washers but differ in hole size — small hole (SKU 7006487) versus large hole (SKU 7006489) — so confirm which you need before ordering. When a position number shows no SKU in the table, that part is not currently available as an individual item on this page; contact our team for guidance.

Main replaceable assemblies on the Hayward SharkVac XL

The SharkVac XL is organised into several logical sub-assemblies that map directly to the numbered positions in the diagram. The top section of the cleaner comprises the dome assembly (pos. 1), clear dome window (pos. 2), dome bushing (pos. 5), and the spring-and-button release mechanism (pos. 3 and 4) that allows the lid to be opened for filter access. Directly beneath sits the filter bucket housing (pos. 6) with its hinged filter door (pos. 7); the drain flaps — a small version at pos. 8, a large version at pos. 9, and a rubber flap at pos. 10 — allow water to drain freely when you lift the unit from the pool. The filter cartridge refill set at pos. 32 (SKU 7015934) is the most frequently replaced consumable on this machine and is designed to be removed, rinsed, and refitted without turning the cleaner over. The drive system runs along the underside of the unit: the drive track with soft thread (pos. 34, SKU 7006460) propels the cleaner across all pool surfaces, while the drive ring (pos. 16), drive pin assembly (pos. 36, SKU 7006485), drive bearing assembly (pos. 37), and idler pulley bearing (pos. 38) transfer power from the motor to the track. The wheel sub-assembly includes the wheel rim with tyre (pos. 12), wheel rim cap (pos. 11), wheel tube (pos. 30, SKU 7006554), and roller end (pos. 17) — all of which are subject to wear from continuous pool-surface contact. The motor assembly at pos. 22 (SKU 7006529) is the heart of the unit, and the power supply at pos. 28 (SKU 7006530) steps down mains current to the safe low-voltage required for in-pool operation; the power cord assembly at pos. 13 carries a 50 µF capacitor rating and connects the two. Sealing integrity is maintained by the compression seal (pos. 41, SKU 7006556), plug seal (pos. 43, SKU 7006490), and the housing connector (pos. 39, SKU 7006486) together with its associated washers (pos. 40 and 42) and Molex connector (pos. 44, SKU 7006557).

Tria entre variants i mides de paquet

The most important variant choice on this diagram is between positions 33a and 33b. Position 33a is the clear T/S brush (SKU 7006493), intended for standard surface scrubbing, while position 33b is the tube wheel with foam roller SV (SKU 7006533) — a softer cleaning head suited to different surface finishes or cleaning preferences; fitting the wrong option will affect both cleaning performance and surface contact, so check your original configuration before ordering. Position 48 also references the tube wheel with foam roller SV (SKU 7006533), confirming that the same roller assembly appears in two locations within the drive train, meaning you may need to order two units if both are worn. The connector washer positions 40 and 42 look similar in the diagram but differ by hole diameter — the small-hole washer (pos. 40, SKU 7006487) and the large-hole washer (pos. 42, SKU 7006489) are not interchangeable, as each seats against a different mating surface in the housing connector. For the screw positions (pos. 25 through 29 and pos. 45), the bill of materials specifies full metric dimensions and drive type — for example, M7×10 mm flat Torx at pos. 25, M7×25 mm flat Torx at pos. 26, M5×35 mm PT at pos. 27, M5×12 mm pan Torx T-20 at pos. 29, and M5×20 mm pan Torx T-20 at pos. 45 — so always match thread diameter, pitch, length, and head style precisely to avoid stripping the plastic housings during reassembly.